Reviews                                                         

Can Radiator Fans and Case Fans Be Used Interchangeably?

Yes, radiator fans and case fans can often be physically interchanged, especially when both use the same 120mm or 140mm mounting pattern. But that does not mean they are thermally interchangeable.

A 120mm fan that looks excellent when tested in open air can lose a meaningful portion of its useful airflow once it is pressed against a dense radiator, dust filter, restrictive mesh panel, or narrow side intake because the fan now has to overcome resistance rather than simply move the largest possible volume of unrestricted air.

I would never choose a radiator fan from free-air airflow numbers alone. And I would not automatically reject a high-static-pressure radiator fan for case duty either. Modern PC fans have blurred the old division between “radiator fan” and “case fan,” but physics has not disappeared.

radiator fans generally work well as case fans, while airflow-focused case fans are much more likely to struggle when used on restrictive radiators.

Radiator Fans vs Case Fans: The Label Is Less Important Than the Fan Curve

The traditional distinction sounds straightforward.

 is optimized to maintain airflow when air must pass through resistance such as radiator fins.

 is generally optimized to move a larger volume of air through relatively unrestricted space.

That leads people to compare static pressure against airflow as though these were two completely separate fan species. They are not.

Every axial PC fan produces both airflow and pressure. The difference is where the fan performs best along its pressure-to-airflow, or 

CORSAIR describes static pressure as the force a fan can exert against obstacles such as heatsinks and radiators, while airflow represents the volume of air moved through a relatively unrestricted environment. That is a far more useful distinction than simply reading “radiator” or “case” on a retail box.

Noctua makes the same point more technically. Its comparison of the NF-F12, NF-S12A, and NF-A12x25 shows that maximum static pressure and maximum free-air airflow represent opposite ends of a fan's operating curve; what matters in a real PC is where that curve intersects the resistance, or impedance, created by the case, heatsink, filter, or radiator.

That is the part spec-sheet shopping tends to hide.

It describes airflow volume, typically measured under conditions with little or no downstream restriction.

A fan rated at 65 CFM is not guaranteed to push 65 CFM through a radiator.

Once resistance increases, actual airflow falls.

This is why an airflow-focused fan can look magnificent on paper and become mediocre when mounted against a thick radiator.

Static pressure for PC fans is commonly listed in 

Higher maximum static pressure generally indicates that the fan can maintain stronger pressure against an obstruction.

But maximum mmH₂O is not the entire answer either.

A 4.0 mmH₂O fan running at 3,000 RPM may look spectacular in a comparison table while being far too loud for the 900–1,300 RPM range you actually use.

Static Pressure vs Airflow Fans: Look at Real 120mm Numbers

Real specifications show why the distinction becomes messy.

FanIntended BiasMax AirflowMax Static PressureMaximum SpeedWhat the Numbers SuggestNoctua NF-S12A PWMAirflow-focused63.27 CFM1.19 mmH₂O1,200 RPMStrong candidate for open case ventilationNoctua NF-A12x25 PWMBalanced / all-round60.09 CFM2.34 mmH₂O2,000 RPMSuitable for case, heatsink, and radiator useARCTIC P12Pressure-focused56.3 CFM2.20 mmH₂O1,800 RPMWell suited to radiators, filters, and restricted intake

. The NF-A12x25 actually has slightly lower maximum free-air CFM yet roughly twice the rated maximum pressure, illustrating why the higher CFM number does not automatically make the NF-S12A the better radiator fan.

ARCTIC's pressure-oriented P12 provides another useful reference point: 

, with an official listed MSRP of US$10.99 on the page retrieved for this analysis.

There is no magical CFM threshold that separates a radiator fan from a case fan.

The blade geometry, frame, motor, RPM range, pressure curve, acoustic behavior, radiator design, and downstream restriction all matter.

And this is exactly why ACEGEEK's existing guide on choosing between radiator-oriented and case-airflow fans treats the job—not the product label—as the deciding factor. 

ACEGEEK guide to choosing radiator or case-airflow fans

But this is where the answer needs a giant asterisk.

A normal case fan can work on an AIO radiator if it generates enough pressure for the radiator's resistance at the RPM range you intend to use.

The problem appears when someone takes an aggressively airflow-biased fan, bolts it against a dense radiator and assumes the free-air CFM specification survives intact.

Air has to pass through a matrix of metal fins. Radiator thickness, fin density, dust buildup, grille geometry and any nearby filter increase the resistance the fan must overcome.

Add a front panel in front of that radiator and things become even more interesting.

front vent → dust filter → fan → radiator → internal case

That is no longer a simple fan test. It is a restriction stack.

This is also why radiator position matters. ACEGEEK's analysis of 

top versus side radiator placement in panoramic cases

 explains that the same radiator can behave differently depending on whether it receives open intake air, sits behind restrictive glass-side geometry, or exhausts already-warmed internal air. 

Top vs Side Radiator in a Panoramic PC Case

Do Radiator Fans Need High Static Pressure?

Usually, yes—but “high” needs context.

A radiator benefits from a fan capable of maintaining useful airflow against the radiator's resistance. High static pressure is therefore desirable, especially with dense or thick heat exchangers.

That does not mean you should sort a shopping page by mmH₂O and buy the biggest number.

And the fan-to-radiator seal matters more than many builders realize. If air escapes around a badly fitting fan frame instead of moving through the fins, the impressive pressure specification printed on the box is doing less useful work.

This direction of the swap is much easier.

Yes, radiator fans can generally be used as case fans.

In fact, I often think the distinction is overstated for modern builds.

A good pressure-capable fan is particularly useful as a case intake when the “case intake” is not really open at all.

Think about what sits in front of many intake fans:

That fan is already operating against resistance.

Calling it a “case fan position” does not remove the obstruction.

This makes high static pressure fans especially sensible behind dust filters and restrictive mesh panels.

Where a Pure Airflow Fan Still Makes Sense

That is where a high-airflow fan can operate closer to the environment its CFM specification represents.

An airflow-focused model may give you the air movement you need with lower RPM and a softer noise profile.

This is why I resist the internet habit of saying “static pressure fans are always better.”

Sometimes you are buying pressure capability that the installation barely needs.

The Best Fan Depends on What Sits 5mm in Front of It

Forget the marketing category for a minute and inspect the actual mounting position.

Fan PositionTypical ResistanceWhat I Would Prioritize120mm fan on AIO radiatorHighStatic pressure, PWM range, sealingFront intake behind fine dust filterMedium to highBalanced or pressure-oriented fanSide intake behind narrow ventsMedium to highStatic pressureBottom intake with filterMediumBalanced pressure and airflowOpen rear exhaustLowAirflow and acousticsOpen top exhaustLow to mediumAirflow, acoustics, RPM controlFan behind radiator + filter + restrictive panelVery highStrong pressure performance

 reaches the same broader conclusion from a system perspective: once radiators, filters, panels and multiple fan banks enter the airflow path, nominal fan counts tell you much less than the resistance each fan is actually fighting. 

How to Plan Airflow for a Dual-Radiator PC Build

The Hidden Problem: A Better Radiator Fan Can Still Make the PC Worse

Here is where component-by-component thinking fails.

Suppose you replace mediocre AIO radiator fans with high static pressure models.

If the radiator is mounted at the front as intake, those fans may now push more radiator-heated air into the case.

Can Radiator Fans and Case Fans Be Used Interchangeably?

Yes, radiator fans and case fans can often be physically interchanged, especially when both use the same 120mm or 140mm mounting pattern. But that does not mean they are thermally interchangeable.

That distinction matters.

Pressure changes everything.

A 120mm fan that looks excellent when tested in open air can lose a meaningful portion of its useful airflow once it is pressed against a dense radiator, dust filter, restrictive mesh panel, or narrow side intake because the fan now has to overcome resistance rather than simply move the largest possible volume of unrestricted air.

So why do we still shop by CFM alone?

I would never choose a radiator fan from free-air airflow numbers alone. And I would not automatically reject a high-static-pressure radiator fan for case duty either. Modern PC fans have blurred the old division between “radiator fan” and “case fan,” but physics has not disappeared.

The practical answer is simple: radiator fans generally work well as case fans, while airflow-focused case fans are much more likely to struggle when used on restrictive radiators.

Radiator Fans vs Case Fans: The Label Is Less Important Than the Fan Curve

The traditional distinction sounds straightforward.

A radiator fan is optimized to maintain airflow when air must pass through resistance such as radiator fins.

A case fan is generally optimized to move a larger volume of air through relatively unrestricted space.

That leads people to compare static pressure against airflow as though these were two completely separate fan species. They are not.

Every axial PC fan produces both airflow and pressure. The difference is where the fan performs best along its pressure-to-airflow, or P/Q, curve.

CORSAIR describes static pressure as the force a fan can exert against obstacles such as heatsinks and radiators, while airflow represents the volume of air moved through a relatively unrestricted environment. That is a far more useful distinction than simply reading “radiator” or “case” on a retail box.

Noctua makes the same point more technically. Its comparison of the NF-F12, NF-S12A, and NF-A12x25 shows that maximum static pressure and maximum free-air airflow represent opposite ends of a fan's operating curve; what matters in a real PC is where that curve intersects the resistance, or impedance, created by the case, heatsink, filter, or radiator.

That is the part spec-sheet shopping tends to hide.

What CFM Actually Tells You

CFM means cubic feet per minute.

It describes airflow volume, typically measured under conditions with little or no downstream restriction.

A fan rated at 65 CFM is not guaranteed to push 65 CFM through a radiator.

Once resistance increases, actual airflow falls.

This is why an airflow-focused fan can look magnificent on paper and become mediocre when mounted against a thick radiator.

What mmH₂O Actually Tells You

Static pressure for PC fans is commonly listed in mmH₂O, or millimeters of water column.

Higher maximum static pressure generally indicates that the fan can maintain stronger pressure against an obstruction.

But maximum mmH₂O is not the entire answer either.

A 4.0 mmH₂O fan running at 3,000 RPM may look spectacular in a comparison table while being far too loud for the 900–1,300 RPM range you actually use.

I care about usable pressure.

Not trophy pressure.

Static Pressure vs Airflow Fans: Look at Real 120mm Numbers

Real specifications show why the distinction becomes messy.

Consider these 120mm fan examples.

FanIntended BiasMax AirflowMax Static PressureMaximum SpeedWhat the Numbers SuggestNoctua NF-S12A PWMAirflow-focused63.27 CFM1.19 mmH₂O1,200 RPMStrong candidate for open case ventilationNoctua NF-A12x25 PWMBalanced / all-round60.09 CFM2.34 mmH₂O2,000 RPMSuitable for case, heatsink, and radiator useARCTIC P12Pressure-focused56.3 CFM2.20 mmH₂O1,800 RPMWell suited to radiators, filters, and restricted intake

Noctua lists the NF-S12A PWM at 63.27 CFM and 1.19 mmH₂O, whereas its NF-A12x25 PWM is rated at 60.09 CFM and 2.34 mmH₂O. The NF-A12x25 actually has slightly lower maximum free-air CFM yet roughly twice the rated maximum pressure, illustrating why the higher CFM number does not automatically make the NF-S12A the better radiator fan.

ARCTIC's pressure-oriented P12 provides another useful reference point: 56.3 CFM, 2.20 mmH₂O, 1,800 RPM, with an official listed MSRP of US$10.99 on the page retrieved for this analysis.

Notice the pattern?

There is no magical CFM threshold that separates a radiator fan from a case fan.

The blade geometry, frame, motor, RPM range, pressure curve, acoustic behavior, radiator design, and downstream restriction all matter.

And this is exactly why ACEGEEK's existing guide on choosing between radiator-oriented and case-airflow fans treats the job—not the product label—as the deciding factor. ACEGEEK guide to choosing radiator or case-airflow fans

Can You Use Case Fans on a Radiator?

Yes.

But this is where the answer needs a giant asterisk.

A normal case fan can work on an AIO radiator if it generates enough pressure for the radiator's resistance at the RPM range you intend to use.

That can be perfectly acceptable on:





relatively thin radiators;



lower fin-density designs;



lightly restricted mounting positions;



systems running modest CPU power;



fans that were already designed as balanced models;



push-pull arrangements where two fan banks share the resistance.

The problem appears when someone takes an aggressively airflow-biased fan, bolts it against a dense radiator and assumes the free-air CFM specification survives intact.

It does not.

Radiators Create Resistance

A radiator is not empty space.

Air has to pass through a matrix of metal fins. Radiator thickness, fin density, dust buildup, grille geometry and any nearby filter increase the resistance the fan must overcome.

Add a front panel in front of that radiator and things become even more interesting.

The effective path might become:

front vent → dust filter → fan → radiator → internal case

That is no longer a simple fan test. It is a restriction stack.

This is also why radiator position matters. ACEGEEK's analysis of top versus side radiator placement in panoramic cases explains that the same radiator can behave differently depending on whether it receives open intake air, sits behind restrictive glass-side geometry, or exhausts already-warmed internal air. Top vs Side Radiator in a Panoramic PC Case

Do Radiator Fans Need High Static Pressure?

Usually, yes—but “high” needs context.

A radiator benefits from a fan capable of maintaining useful airflow against the radiator's resistance. High static pressure is therefore desirable, especially with dense or thick heat exchangers.

That does not mean you should sort a shopping page by mmH₂O and buy the biggest number.

RPM matters.

Noise matters.

The complete P/Q curve matters.

And the fan-to-radiator seal matters more than many builders realize. If air escapes around a badly fitting fan frame instead of moving through the fins, the impressive pressure specification printed on the box is doing less useful work.



Can Radiator Fans Be Used as Case Fans?

This direction of the swap is much easier.

Yes, radiator fans can generally be used as case fans.

In fact, I often think the distinction is overstated for modern builds.

A good pressure-capable fan is particularly useful as a case intake when the “case intake” is not really open at all.

Think about what sits in front of many intake fans:





dust filter;



fine mesh;



narrow side vents;



decorative front fascia;



drive cage;



cable obstruction;



angled louvers;



radiator.

That fan is already operating against resistance.

Calling it a “case fan position” does not remove the obstruction.

This makes high static pressure fans especially sensible behind dust filters and restrictive mesh panels.

Where a Pure Airflow Fan Still Makes Sense

Now take a rear exhaust mount.

No radiator.

No filter.

Large open grille.

Minimal obstruction.

That is where a high-airflow fan can operate closer to the environment its CFM specification represents.

An airflow-focused model may give you the air movement you need with lower RPM and a softer noise profile.

This is why I resist the internet habit of saying “static pressure fans are always better.”

Sometimes they are.

Sometimes you are buying pressure capability that the installation barely needs.

The Best Fan Depends on What Sits 5mm in Front of It

Forget the marketing category for a minute and inspect the actual mounting position.

Fan PositionTypical ResistanceWhat I Would Prioritize120mm fan on AIO radiatorHighStatic pressure, PWM range, sealingFront intake behind fine dust filterMedium to highBalanced or pressure-oriented fanSide intake behind narrow ventsMedium to highStatic pressureBottom intake with filterMediumBalanced pressure and airflowOpen rear exhaustLowAirflow and acousticsOpen top exhaustLow to mediumAirflow, acoustics, RPM controlFan behind radiator + filter + restrictive panelVery highStrong pressure performance

This is the decision framework I trust.

Not the label.

ACEGEEK's dual-radiator airflow guide reaches the same broader conclusion from a system perspective: once radiators, filters, panels and multiple fan banks enter the airflow path, nominal fan counts tell you much less than the resistance each fan is actually fighting. How to Plan Airflow for a Dual-Radiator PC Build

The Hidden Problem: A Better Radiator Fan Can Still Make the PC Worse

Here is where component-by-component thinking fails.

Suppose you replace mediocre AIO radiator fans with high static pressure models.

CPU temperature drops.

Success?

Maybe.

If the radiator is mounted at the front as intake, those fans may now push more radiator-heated air into the case.

The CPU wins.

The GPU may not.

This is why I never evaluate an AIO fan change using CPU package temperature alone. I would record at least:





CPU package temperature;



GPU core temperature;



GPU hotspot temperature;



coolant temperature if available;



fan RPM;



room temperature;



noise level;



sustained clock behavior.

ACEGEEK's guide to balancing CPU cooling and GPU airflow makes the same system-level point: optimizing one temperature sensor can create worse airflow for another component if the chassis routing is wrong. How to Balance CPU Cooling and GPU Airflow in the Same System

And this becomes more important as GPU heat output rises.

A front radiator does not delete heat. It moves that heat into air.

Where does that air go next?

AIO Radiator Fans: What I Would Check Before Replacing Them

If you are replacing the fans included with a 240mm, 280mm, or 360mm AIO, I would check seven things before buying anything.

1. Fan Size

Match the radiator format.

A 240mm or 360mm radiator normally uses 120mm fans.

A 280mm radiator normally uses 140mm fans.

Simple, but worth stating.

2. Static Pressure

Look at mmH₂O, but do not judge it in isolation.

The pressure figure should be considered alongside maximum RPM and acoustics.

3. PWM Control

For a modern performance PC, I strongly prefer 4-pin PWM fans.

There is little reason to make radiator fans run harder than the coolant or CPU load requires.

4. RPM Range

A fan that can hit 2,500 RPM is not automatically superior.

Ask what it does at 800, 1,000, 1,200 and 1,500 RPM—the speeds you may actually tolerate.

5. Frame Design

A radiator fan benefits from a frame that seals reasonably well against the radiator surface.

Large gaps encourage bypass airflow.

6. Noise Character

Two fans can measure similarly in dB(A) yet sound completely different.

Motor hum, bearing noise, blade-pass tone and resonance against the radiator all affect perceived noise.

7. Your Case Airflow

Do not fix the radiator while ignoring the chassis.

If the system has too little intake, badly placed exhaust, or a GPU starved behind glass, changing one fan model will not repair the airflow architecture.

ACEGEEK's current PC case range includes chassis supporting 240mm and 360mm liquid cooling configurations, which is another reason fan choice should be evaluated together with the radiator mounting geometry rather than as a standalone accessory decision. ACEGEEK PC cases and liquid-cooling support

When I Would Reuse the Same Fan Model Everywhere

There is nothing inherently wrong with using one good fan model for radiator, intake and exhaust positions.

Actually, it can simplify a build.

You get:





consistent acoustics;



matching RGB behavior;



identical PWM response;



easier spare-part management;



cleaner visual design;



fewer controller compatibility headaches.

The key is choosing a genuinely balanced fan.

Noctua explicitly designed the NF-A12x25 around this idea. Its published P/Q comparison positions the model between the pressure-specialized NF-F12 and airflow-specialized NF-S12A, optimizing the middle portion of the curve where typical cases, heatsinks and radiators actually operate. Noctua NF-A12x25 P/Q performance comparison

That is what a real “all-rounder” fan should mean.

Not merely a box that says “works everywhere.”

When I Would Not Swap the Fans

I would keep the original radiator fans—or replace them only with another pressure-capable model—when dealing with:





thick radiators;



dense fin stacks;



radiator-plus-filter combinations;



heavily restricted front panels;



high-power CPUs running long all-core workloads;



low-RPM silence-focused configurations where efficiency matters;



systems already close to their thermal or acoustic limit.

Likewise, I would not replace a quiet open-air exhaust fan with a much faster pressure fan merely because the pressure number looks impressive.

More RPM can hide bad fan selection.

Until you hear it.

Test the Swap Instead of Arguing About It

The best part is that this question is testable.

Run a controlled baseline.

I would use a repeatable CPU workload or a simultaneous CPU/GPU workload for at least long enough to reach thermal equilibrium, record ambient room temperature, and note fan speed rather than simply setting every fan to 100%.

Then change only the fan.

Keep:





workload identical;



fan orientation identical;



case panels installed;



radiator position identical;



pump speed identical;



room temperature as stable as practical.

Compare temperature delta over ambient, not only absolute CPU temperature.

If the room was 21°C during one test and 26°C during another, a raw component-temperature comparison can mislead you.

And do not stop at CPU temperature.

If a new front-radiator fan reduces CPU temperature by 3°C but raises GPU hotspot by 6°C, I would not call that an automatic thermal upgrade.

Systems have more than one sensor.

FAQs

Can radiator fans and case fans be used interchangeably?

Radiator fans and case fans can usually be interchanged physically when they share the same 120mm or 140mm mounting dimensions, but they are not always interchangeable thermally because radiator fins create greater airflow resistance and therefore reward fans that maintain useful airflow under higher static pressure.

A pressure-oriented radiator fan will normally work fine as a case fan. An airflow-focused case fan is the riskier swap because its performance may fall substantially when placed directly against a restrictive radiator.

Can you use case fans on a radiator?

Case fans can be used on a radiator when they provide enough static pressure to move air through the radiator's fin stack at the intended RPM, but airflow-focused models may lose more useful airflow under restriction than fans designed around stronger pressure performance.

The thinner and less restrictive the radiator, the easier the swap becomes. Dense radiators, filters and restrictive case panels raise pressure demand.

Can radiator fans be used as case fans?

Radiator fans can generally be used as case fans because high-static-pressure capability does not prevent a fan from moving open-air volume, and that extra pressure capability can actually help at filtered front, side or bottom intake positions where the case itself creates meaningful airflow resistance.

The main trade-offs are usually price, maximum RPM and acoustics rather than compatibility. For a completely open rear exhaust, an airflow-focused fan may still be quieter or more efficient for the job.

Do radiator fans need high static pressure?

Radiator fans generally benefit from high static pressure because radiator fins resist airflow, forcing the fan to maintain pressure while moving air through narrow passages, although the useful figure is performance along the complete pressure-to-airflow curve at realistic RPM rather than the maximum mmH₂O number alone.

A fan producing huge pressure only at an intolerably loud speed is not automatically the best radiator fan for a quiet gaming PC.

What are the best fans for radiators?

The best fans for radiators are pressure-capable PWM fans that maintain useful airflow through the radiator at realistic operating speeds while producing acceptable noise, providing a good frame seal, and matching the radiator's 120mm or 140mm mounting format and the cooling demands of the CPU.

Models designed as balanced all-rounders can also perform extremely well. Noctua's NF-A12x25, for example, is rated at 60.09 CFM and 2.34 mmH₂O and is explicitly engineered around radiator, heatsink and case operating resistance.

Is static pressure or CFM more important for PC cooling?

Static pressure becomes more important when a PC fan faces radiators, filters, dense mesh or narrow vents, while CFM becomes more useful when airflow is relatively unrestricted; neither specification alone can predict real cooling because actual airflow occurs where the fan's P/Q curve meets the resistance of the installation.

For an open rear exhaust, I would pay more attention to airflow and noise. For a radiator or heavily filtered intake, I would put far more weight on pressure behavior.

Choose Fans for the Resistance They Actually Face

Stop asking whether the box says “radiator fan” or “case fan.”

Look behind the fan.

If you see radiator fins, a dense dust filter, restrictive mesh or narrow ventilation slots, choose a fan that can hold useful airflow against pressure.

If you see an open exhaust path, prioritize airflow, acoustics and the RPM range you actually intend to run.

And if you want one fan model throughout the entire build, choose a well-balanced 120mm or 140mm PWM design with a strong P/Q curve rather than chasing either the biggest CFM figure or the biggest mmH₂O number.

Radiator fans can usually become case fans without drama. Case fans can become radiator fans only when their pressure performance is good enough for the resistance in front of them.

That is the answer I would build around.

Before purchasing more fans, map every intake, exhaust, filter and radiator in your system, check ACEGEEK's guides to radiator airflow and PC case cooling, then test the finished configuration under the workloads you actually run. Buy for the airflow path—not the marketing category.

Can radiator fans and case fans be used interchangeably? We compare static pressure, airflow, CFM, mmH₂O, radiator resistance, noise, and real 120mm fan specifications to show where each fan actually works best.

التقييمات

هل يمكن استخدام مراوح المبرد ومراوح صندوق الحاسوب بشكل متبادل؟ نقارن الضغط الساكن، وتدفق الهواء، وCFM، وmmH₂O، ومقاومة المبرد، والضوضاء، ومواصفات مراوح 120 مم الفعلية لنوضح أين تعمل كل مروحة بشكل أفضل.

هل يمكن استخدام مراوح المبرد ومراوح صندوق الحاسوب بشكل متبادل؟

How to Know Whether a Fan Is Best for Radiators or Case Airflow

The Ugly Truth Behind Static Pressure vs Airflow Fans

A fan is not “good” by itself. It is only good at a job.

A 120mm fan with a loud CFM number can look dominant on a product page, but once you bolt it to a 360mm AIO radiator, shove it behind a dust filter, or trap it behind a decorative front panel with tiny side vents, that proud airflow rating can collapse into noise, turbulence, and buyer regret. So why do we still let CFM alone make the decision?

The real question is not “Which fan is best?” The real question is: 

A high static pressure fan is built to push air through resistance: radiator fins, thick dust filters, dense mesh, cable clutter, and tight intake gaps. An airflow fan is built to move more open-air volume when there is less obstruction. This is exactly why AceGeek’s guide on 

why cooler specs alone do not predict real thermal results

 gets the core issue right: CFM and static pressure are not separate trophies. They are clues.

Radiator Fans vs Case Fans: The Job Decides the Winner

Radiators are resistance machines. Case airflow is route management.

That sounds simple, but most bad PC cooling advice comes from ignoring it. A radiator is a wall of metal fins full of narrow channels. The fan must force air through that fin stack. A case intake, by contrast, usually needs to pull cool air into the chassis and send it toward heat sources: GPU, CPU cooler, VRM, RAM, M.2 SSDs, and the PSU-adjacent dead zones nobody photographs.

For radiators, I care about static pressure, RPM behavior, bearing quality, and noise tone. For case airflow, I care about CFM, blade sweep, open-area intake, pressure balance, and whether the fan is feeding the GPU or just decorating a glass box.

radiator fans vs case fans is not a brand debate. It is a restriction debate.

A 240mm, 280mm, or 360mm AIO radiator needs fans that can hold airflow against impedance. A wide-open rear exhaust mount does not. A front mesh intake might reward airflow fans. A side-mounted radiator behind a filter might punish them. AceGeek’s breakdown of 

why radiator thickness breaks otherwise compatible builds

 makes the same point from the case side: thickness, fin density, dust, and clearance all raise the pressure demand.

I do not trust “universal fan” marketing. Not much.

Yes, some modern fans are decent hybrids. But when a seller tells you one fan is perfect for every radiator, every mesh panel, every fish-tank case, every dust filter, and every RPM range, I hear a sales department trying to erase physics.

The Numbers That Matter: CFM, Static Pressure, RPM, dBA, and PWM

If you want the short version, use this rule: 

CFM tells you how much air a fan can move in low restriction; static pressure tells you how well it can keep moving air when something blocks the path.

You also need RPM, dBA, PWM control, blade design, frame sealing, bearing type, and real mounting position. A fan rated at 75 CFM in open air may disappoint on a dense radiator. A fan rated at 2.5 mmH₂O static pressure may perform beautifully on a radiator but sound rough if you run it too fast on a side intake near your ear.

And yes, noise quality matters. A low dBA number does not always mean a pleasant sound. Motor whine, bearing tick, resonance against a radiator, and fan curve spikes can make a technically “quiet” fan feel irritating after 20 minutes.

This is where 4-pin PWM control earns its keep. AceGeek’s 

 explains the control difference clearly: 3-pin fans use voltage control, while 4-pin PWM fans use a dedicated control signal for smoother speed changes. In real builds, PWM is not luxury. It is how you stop the fan curve from behaving like a panic attack.

Spec or ConditionWhat It Really MeansBest for RadiatorsBest for Case AirflowMy Blunt TakeStatic pressure, often mmH₂OAbility to push air through resistanceYesSometimesPrioritize this for radiators, filters, and tight panelsCFMOpen-air volume moved per minuteSometimesYesUseful only when the intake or exhaust path is not chokedRPMRotation speedDependsDependsMore RPM can help, but it often buys performance with noisedBAMeasured sound levelDependsDependsLook for tone and curve behavior, not just one lab numberPWM / 4-pinFine speed control through motherboard signalYesYesI would avoid serious builds without PWM fan controlRadiator thicknessMore core depth means more resistanceYesNoThick radiators need pressure and clearance, not wishful thinkingMesh front panelLower intake resistanceSometimesYesAirflow fans can shine when the case actually breathesGlass or restricted front panelNarrower intake pathYesSometimesStatic pressure may help, but bad intake geometry is still bad

Why High-Heat PCs Expose Bad Fan Choices Fast

Modern PCs are not gentle thermal environments anymore.

Intel lists the Core i9-14900K at 125 W Processor Base Power and 253 W Maximum Turbo Power on its 

. NVIDIA lists the GeForce RTX 4090 at 450 W Total Graphics Power, 24 GB GDDR6X, a 61 mm 3-slot thickness, and an 850 W recommended system power target on its 

Do the ugly math. A 253 W CPU plus a 450 W GPU is already a 703 W heat-management problem before motherboard VRMs, DDR5, NVMe drives, RGB controllers, pump heat, PSU losses, and dust enter the conversation.

That is why I roll my eyes at fan-count obsession. Six mediocre fans in a confused layout can lose to three good fans with a clean intake path. The best fan for case airflow is not the one that fills every mount. It is the one that feeds the part creating the heat.

PC case airflow design rules for OEM and SI thermal planning

 fit this topic naturally. Airflow is not a vibe. It is a path: intake, component contact, exhaust, repeat. Break the path and the fans become expensive decoration.

The data center industry is dealing with the same lesson at a larger scale. The U.S. Department of Energy reported that data centers consumed about 4.4% of total U.S. electricity in 2023 and could reach roughly 6.7% to 12% by 2028, with electricity use rising from 58 TWh in 2014 to 176 TWh in 2023 in its 

. Berkeley Lab’s summary adds that data-center power demand more than doubled between 2017 and 2023, largely because of AI servers and their cooling needs in the 

2024 U.S. data center energy usage report summary

Reuters put it even more sharply in its 2025 report on 

heat as a key challenge for data centers and AI

, noting that high-powered AI and cloud servers generate intense heat that can exceed traditional air-cooling limits. I am not saying your mid-tower is a hyperscale rack. I am saying the cooling principle is not negotiable: density punishes lazy airflow assumptions.

A fan is best for radiators when it can maintain airflow through fin resistance without needing absurd RPM or producing an unbearable tone.

For an AIO radiator fan vs case fan decision, I start with radiator position.

Top exhaust radiator? Use pressure-capable fans and make sure the case has enough front or bottom intake to feed the GPU. Front intake radiator? Pressure matters even more, but now you must watch GPU temperature because the radiator can warm the air before it reaches the graphics card. Side radiator? Check panel restriction, tube routing, and whether the fan is pulling through glass-side geometry that looks clean but breathes poorly.

 is a smart internal link here because it addresses the CPU-versus-GPU compromise many buyers miss. A front radiator can improve CPU temperature while nudging GPU temperature upward. That is not failure. That is tradeoff.

A fan is best for case airflow when it moves a large volume of air through a low-resistance path and supports a coherent pressure plan inside the chassis.

That last phrase matters: coherent pressure plan.

For a normal mesh-front ATX case, I usually prefer strong intake at the front or bottom, then controlled exhaust at the rear and top. For a dual-chamber or fish-tank style case, side and bottom intake often matter more because the GPU needs direct air. For compact M-ATX builds, every cable and drive cage becomes part of the airflow story.

If the fan sits on an open rear exhaust, CFM can matter more than static pressure. If it sits behind a thick dust filter, narrow side vent, or restrictive decorative front, static pressure becomes more valuable even though the fan is technically being used as a “case fan.”

This is why the phrase “airflow fan for PC case” can mislead buyers. The case determines whether the fan sees open air or resistance.

, with top, side, rear, and bottom fan support plus 420mm or 360mm top AIO support, gives builders more ways to separate CPU radiator exhaust from GPU intake. A roomier case like the 

 gives E-ATX support, a 410mm GPU clearance figure, and top 360mm radiator support. Those details are not filler. They decide whether your fan plan has space to work.

And for disciplined smaller systems, the 

 shows the tradeoff clearly: compact dimensions, 285mm GPU clearance, top 240mm radiator support, and fewer places to hide sloppy airflow. That can be fine. But it means you should stop pretending a compact budget shell can absorb flagship heat without discipline.

My Field Rule: Choose the Fan After You Map the Obstruction

I would rather see a builder spend ten minutes mapping obstruction than spend $80 chasing prettier fan packaging.

But here is the uncomfortable part: many users are not choosing between a perfect radiator fan and a perfect airflow fan. They are choosing between a fan that works acceptably in both roles and a layout that ruins both roles.

What is the difference between static pressure and airflow fans?

Static pressure vs airflow fans is the practical choice between a fan built to push air through resistance and a fan built to move a larger volume of air through open space, with radiator fins, dust filters, mesh panels, and tight clearances deciding which design actually performs better. After that, the mounting location tells you the rest.

Static pressure fans usually make more sense on radiators, dense filters, and restricted front panels. Airflow fans usually make more sense on open intake and exhaust mounts. Hybrid fans can work, but I still want to know the job before I trust the label.

Radiator fans and case fans can use the same 120mm or 140mm physical size, but they are not always optimized for the same airflow job because radiators create fin resistance while case mounts may have low or high restriction depending on panel design. That is the whole trap behind “one fan fits all” advice.

A radiator fan should hold pressure through a fin stack. A case fan should support the case’s intake and exhaust path. Sometimes one model can do both well enough. Sometimes it cannot.

Is static pressure or CFM more important for PC cooling?

Static pressure is more important when the fan faces resistance, while CFM is more important when the fan has a relatively open path, so neither number is universally superior without knowing the radiator, filter, panel, and mounting position. The best spec is the one tied to the actual obstruction in the build.

For a 360mm AIO, I care more about pressure and PWM behavior. For a rear exhaust fan, I care more about smooth open-air flow and low noise. For a filtered intake, I look at both.

Can I use high static pressure fans as case fans?

High static pressure fans can work as case fans, especially when the case has restrictive filters, narrow vents, or dense mesh, but they may not always outperform airflow-focused fans on wide-open mounts where volume, blade sweep, and acoustic smoothness matter more. In other words, they are useful, not magic.

I often prefer pressure-capable fans in messy real-world cases because dust filters and decorative panels add resistance. But in a clean mesh case with open intakes, a good airflow fan can still be the better pick.

How do I choose radiator fans for an AIO cooler?

Choose radiator fans for an AIO cooler by matching fan pressure, PWM control, noise behavior, and radiator thickness to the actual mounting position, then check whether the radiator will act as intake or exhaust inside the case. AIO radiator fan choice is not only about CPU temperature; it also changes GPU airflow.

For top exhaust AIOs, make sure the case still feeds the GPU. For front intake AIOs, watch GPU temperature. For side-mounted AIOs, check panel restriction and tube routing. The fan is only one part of the system.

The best fan for case airflow is the fan that moves enough air through the case’s real intake and exhaust path without excessive noise, turbulence, or pressure imbalance, while feeding the hottest components instead of simply filling every fan mount. In many gaming PCs, that means prioritizing GPU intake first.

A mesh-front case may reward airflow fans. A glass-front case may need pressure-capable fans. A compact case may need fewer but better-positioned PWM fans. Do not buy the fan before you understand the airflow lane.

Your Next Steps: Stop Buying Fan Specs Blind

Here is the move I recommend: open your case plan and label every fan position as 

. Then choose the fan type for that job instead of buying one shiny model and hoping the build forgives you.

If the fan is fighting fins, filters, or tight panels, go static pressure. If the fan has a clean open path, go airflow. If the case has a high-watt CPU, a 300 W to 450 W GPU, a thick radiator, and a glass-heavy front, stop pretending the fan spec sheet will save a bad layout.

Audit the obstruction. Choose the fan. Tune the curve. Then test CPU package temperature, GPU hotspot, fan RPM, and noise under the workload you actually use.

That is how to know whether a fan is best for radiators or case airflow. Not by the box. By the job.

How to Know Whether a Fan Is Best for Radiators or Case Airflow

The Ugly Truth Behind Static Pressure vs Airflow Fans

A fan is not “good” by itself. It is only good at a job.

Specs lie often.

A 120mm fan with a loud CFM number can look dominant on a product page, but once you bolt it to a 360mm AIO radiator, shove it behind a dust filter, or trap it behind a decorative front panel with tiny side vents, that proud airflow rating can collapse into noise, turbulence, and buyer regret. So why do we still let CFM alone make the decision?

The real question is not “Which fan is best?” The real question is: what is the fan fighting against?

That is where static pressure vs airflow fans becomes useful. Not academic. Useful.

A high static pressure fan is built to push air through resistance: radiator fins, thick dust filters, dense mesh, cable clutter, and tight intake gaps. An airflow fan is built to move more open-air volume when there is less obstruction. This is exactly why AceGeek’s guide on why cooler specs alone do not predict real thermal results gets the core issue right: CFM and static pressure are not separate trophies. They are clues.

And clues need context.

Radiator Fans vs Case Fans: The Job Decides the Winner

Radiators are resistance machines. Case airflow is route management.

That sounds simple, but most bad PC cooling advice comes from ignoring it. A radiator is a wall of metal fins full of narrow channels. The fan must force air through that fin stack. A case intake, by contrast, usually needs to pull cool air into the chassis and send it toward heat sources: GPU, CPU cooler, VRM, RAM, M.2 SSDs, and the PSU-adjacent dead zones nobody photographs.

For radiators, I care about static pressure, RPM behavior, bearing quality, and noise tone. For case airflow, I care about CFM, blade sweep, open-area intake, pressure balance, and whether the fan is feeding the GPU or just decorating a glass box.

Here is the hard truth: radiator fans vs case fans is not a brand debate. It is a restriction debate.

A 240mm, 280mm, or 360mm AIO radiator needs fans that can hold airflow against impedance. A wide-open rear exhaust mount does not. A front mesh intake might reward airflow fans. A side-mounted radiator behind a filter might punish them. AceGeek’s breakdown of why radiator thickness breaks otherwise compatible builds makes the same point from the case side: thickness, fin density, dust, and clearance all raise the pressure demand.

I do not trust “universal fan” marketing. Not much.

Yes, some modern fans are decent hybrids. But when a seller tells you one fan is perfect for every radiator, every mesh panel, every fish-tank case, every dust filter, and every RPM range, I hear a sales department trying to erase physics.

The Numbers That Matter: CFM, Static Pressure, RPM, dBA, and PWM

If you want the short version, use this rule: CFM tells you how much air a fan can move in low restriction; static pressure tells you how well it can keep moving air when something blocks the path.

But that rule is still incomplete.

You also need RPM, dBA, PWM control, blade design, frame sealing, bearing type, and real mounting position. A fan rated at 75 CFM in open air may disappoint on a dense radiator. A fan rated at 2.5 mmH₂O static pressure may perform beautifully on a radiator but sound rough if you run it too fast on a side intake near your ear.

And yes, noise quality matters. A low dBA number does not always mean a pleasant sound. Motor whine, bearing tick, resonance against a radiator, and fan curve spikes can make a technically “quiet” fan feel irritating after 20 minutes.

This is where 4-pin PWM control earns its keep. AceGeek’s 3-pin vs 4-pin PC fan guide explains the control difference clearly: 3-pin fans use voltage control, while 4-pin PWM fans use a dedicated control signal for smoother speed changes. In real builds, PWM is not luxury. It is how you stop the fan curve from behaving like a panic attack.

Fan Spec Translation Table

Spec or ConditionWhat It Really MeansBest for RadiatorsBest for Case AirflowMy Blunt TakeStatic pressure, often mmH₂OAbility to push air through resistanceYesSometimesPrioritize this for radiators, filters, and tight panelsCFMOpen-air volume moved per minuteSometimesYesUseful only when the intake or exhaust path is not chokedRPMRotation speedDependsDependsMore RPM can help, but it often buys performance with noisedBAMeasured sound levelDependsDependsLook for tone and curve behavior, not just one lab numberPWM / 4-pinFine speed control through motherboard signalYesYesI would avoid serious builds without PWM fan controlRadiator thicknessMore core depth means more resistanceYesNoThick radiators need pressure and clearance, not wishful thinkingMesh front panelLower intake resistanceSometimesYesAirflow fans can shine when the case actually breathesGlass or restricted front panelNarrower intake pathYesSometimesStatic pressure may help, but bad intake geometry is still bad

Why High-Heat PCs Expose Bad Fan Choices Fast

Modern PCs are not gentle thermal environments anymore.

Intel lists the Core i9-14900K at 125 W Processor Base Power and 253 W Maximum Turbo Power on its official processor specification page. NVIDIA lists the GeForce RTX 4090 at 450 W Total Graphics Power, 24 GB GDDR6X, a 61 mm 3-slot thickness, and an 850 W recommended system power target on its official RTX 4090 specification page.

Do the ugly math. A 253 W CPU plus a 450 W GPU is already a 703 W heat-management problem before motherboard VRMs, DDR5, NVMe drives, RGB controllers, pump heat, PSU losses, and dust enter the conversation.

That is why I roll my eyes at fan-count obsession. Six mediocre fans in a confused layout can lose to three good fans with a clean intake path. The best fan for case airflow is not the one that fills every mount. It is the one that feeds the part creating the heat.

For gaming PCs, that is often the GPU.

This is also why AceGeek’s PC case airflow design rules for OEM and SI thermal planning fit this topic naturally. Airflow is not a vibe. It is a path: intake, component contact, exhaust, repeat. Break the path and the fans become expensive decoration.

The data center industry is dealing with the same lesson at a larger scale. The U.S. Department of Energy reported that data centers consumed about 4.4% of total U.S. electricity in 2023 and could reach roughly 6.7% to 12% by 2028, with electricity use rising from 58 TWh in 2014 to 176 TWh in 2023 in its data center electricity demand report. Berkeley Lab’s summary adds that data-center power demand more than doubled between 2017 and 2023, largely because of AI servers and their cooling needs in the 2024 U.S. data center energy usage report summary.

Different scale. Same physics.

Heat has to go somewhere.

Reuters put it even more sharply in its 2025 report on heat as a key challenge for data centers and AI, noting that high-powered AI and cloud servers generate intense heat that can exceed traditional air-cooling limits. I am not saying your mid-tower is a hyperscale rack. I am saying the cooling principle is not negotiable: density punishes lazy airflow assumptions.



When a Fan Is Best for Radiators

A fan is best for radiators when it can maintain airflow through fin resistance without needing absurd RPM or producing an unbearable tone.

Look for these signals:





Static pressure rating that stays meaningful at usable RPM



4-pin PWM control



Good frame seal against the radiator



Stable bearing behavior when mounted horizontally or vertically



Smooth acoustic profile between roughly 800 and 1,600 RPM



Enough pressure for the radiator thickness and fin density



No major performance collapse behind a filter or mesh layer

For an AIO radiator fan vs case fan decision, I start with radiator position.

Top exhaust radiator? Use pressure-capable fans and make sure the case has enough front or bottom intake to feed the GPU. Front intake radiator? Pressure matters even more, but now you must watch GPU temperature because the radiator can warm the air before it reaches the graphics card. Side radiator? Check panel restriction, tube routing, and whether the fan is pulling through glass-side geometry that looks clean but breathes poorly.

AceGeek’s article on front-mounted AIO thermal tradeoffs is a smart internal link here because it addresses the CPU-versus-GPU compromise many buyers miss. A front radiator can improve CPU temperature while nudging GPU temperature upward. That is not failure. That is tradeoff.

The fan has to match the tradeoff.

When a Fan Is Best for Case Airflow

A fan is best for case airflow when it moves a large volume of air through a low-resistance path and supports a coherent pressure plan inside the chassis.

That last phrase matters: coherent pressure plan.

For a normal mesh-front ATX case, I usually prefer strong intake at the front or bottom, then controlled exhaust at the rear and top. For a dual-chamber or fish-tank style case, side and bottom intake often matter more because the GPU needs direct air. For compact M-ATX builds, every cable and drive cage becomes part of the airflow story.

If the fan sits on an open rear exhaust, CFM can matter more than static pressure. If it sits behind a thick dust filter, narrow side vent, or restrictive decorative front, static pressure becomes more valuable even though the fan is technically being used as a “case fan.”

This is why the phrase “airflow fan for PC case” can mislead buyers. The case determines whether the fan sees open air or resistance.

A case like the LunarisFlow airflow case, with top, side, rear, and bottom fan support plus 420mm or 360mm top AIO support, gives builders more ways to separate CPU radiator exhaust from GPU intake. A roomier case like the Cruiser L460 Pro airflow case gives E-ATX support, a 410mm GPU clearance figure, and top 360mm radiator support. Those details are not filler. They decide whether your fan plan has space to work.

And for disciplined smaller systems, the Vault M-ATX airflow budget case shows the tradeoff clearly: compact dimensions, 285mm GPU clearance, top 240mm radiator support, and fewer places to hide sloppy airflow. That can be fine. But it means you should stop pretending a compact budget shell can absorb flagship heat without discipline.

My Field Rule: Choose the Fan After You Map the Obstruction

I would rather see a builder spend ten minutes mapping obstruction than spend $80 chasing prettier fan packaging.

Here is my decision process:





Is the fan pushing through a radiator, dense filter, tight front panel, or mesh with limited open area? Choose a high static pressure fan.



Is the fan mounted in a low-resistance front intake, bottom intake, or rear exhaust? Choose an airflow-focused fan.



Is the case glass-heavy or side-vented? Treat it as restricted until proven otherwise.



Is the radiator 280mm, 360mm, thick, or high-FPI? Bias harder toward static pressure.



Is the GPU the biggest heat source? Feed it first.



Does the fan lack PWM? I would not use it for a serious thermal plan unless the build is low-power and cheap by design.

But here is the uncomfortable part: many users are not choosing between a perfect radiator fan and a perfect airflow fan. They are choosing between a fan that works acceptably in both roles and a layout that ruins both roles.

A good fan cannot rescue a bad path.

FAQs

What is the difference between static pressure and airflow fans?

Static pressure vs airflow fans is the practical choice between a fan built to push air through resistance and a fan built to move a larger volume of air through open space, with radiator fins, dust filters, mesh panels, and tight clearances deciding which design actually performs better. After that, the mounting location tells you the rest.

Static pressure fans usually make more sense on radiators, dense filters, and restricted front panels. Airflow fans usually make more sense on open intake and exhaust mounts. Hybrid fans can work, but I still want to know the job before I trust the label.

Are radiator fans the same as case fans?

Radiator fans and case fans can use the same 120mm or 140mm physical size, but they are not always optimized for the same airflow job because radiators create fin resistance while case mounts may have low or high restriction depending on panel design. That is the whole trap behind “one fan fits all” advice.

A radiator fan should hold pressure through a fin stack. A case fan should support the case’s intake and exhaust path. Sometimes one model can do both well enough. Sometimes it cannot.

Is static pressure or CFM more important for PC cooling?

Static pressure is more important when the fan faces resistance, while CFM is more important when the fan has a relatively open path, so neither number is universally superior without knowing the radiator, filter, panel, and mounting position. The best spec is the one tied to the actual obstruction in the build.

For a 360mm AIO, I care more about pressure and PWM behavior. For a rear exhaust fan, I care more about smooth open-air flow and low noise. For a filtered intake, I look at both.

Can I use high static pressure fans as case fans?

High static pressure fans can work as case fans, especially when the case has restrictive filters, narrow vents, or dense mesh, but they may not always outperform airflow-focused fans on wide-open mounts where volume, blade sweep, and acoustic smoothness matter more. In other words, they are useful, not magic.

I often prefer pressure-capable fans in messy real-world cases because dust filters and decorative panels add resistance. But in a clean mesh case with open intakes, a good airflow fan can still be the better pick.

How do I choose radiator fans for an AIO cooler?

Choose radiator fans for an AIO cooler by matching fan pressure, PWM control, noise behavior, and radiator thickness to the actual mounting position, then check whether the radiator will act as intake or exhaust inside the case. AIO radiator fan choice is not only about CPU temperature; it also changes GPU airflow.

For top exhaust AIOs, make sure the case still feeds the GPU. For front intake AIOs, watch GPU temperature. For side-mounted AIOs, check panel restriction and tube routing. The fan is only one part of the system.

What is the best fan for case airflow?

The best fan for case airflow is the fan that moves enough air through the case’s real intake and exhaust path without excessive noise, turbulence, or pressure imbalance, while feeding the hottest components instead of simply filling every fan mount. In many gaming PCs, that means prioritizing GPU intake first.

A mesh-front case may reward airflow fans. A glass-front case may need pressure-capable fans. A compact case may need fewer but better-positioned PWM fans. Do not buy the fan before you understand the airflow lane.

Your Next Steps: Stop Buying Fan Specs Blind

Here is the move I recommend: open your case plan and label every fan position as radiator, filtered intake, open intake, rear exhaust, top exhaust, or side intake. Then choose the fan type for that job instead of buying one shiny model and hoping the build forgives you.

If the fan is fighting fins, filters, or tight panels, go static pressure. If the fan has a clean open path, go airflow. If the case has a high-watt CPU, a 300 W to 450 W GPU, a thick radiator, and a glass-heavy front, stop pretending the fan spec sheet will save a bad layout.

Audit the obstruction. Choose the fan. Tune the curve. Then test CPU package temperature, GPU hotspot, fan RPM, and noise under the workload you actually use.

That is how to know whether a fan is best for radiators or case airflow. Not by the box. By the job.

Learn how to tell whether a PC fan is better for radiators or case airflow by reading static pressure, CFM, RPM, noise, PWM control, radiator restriction, and real system heat load.

تعرف على كيفية تحديد ما إذا كانت مروحة الكمبيوتر أفضل للمبردات أو لتدفق الهواء داخل الهيكل من خلال قراءة الضغط الساكن، وCFM، وRPM، والضوضاء، والتحكم في PWM، وتقييد المبرد، وحمل الحرارة الفعلي للنظام.

كيفية معرفة ما إذا كانت المروحة هي الأنسب للمبردات أو لتدفق الهواء داخل صندوق الحاسوب

تقدم شركة Acegeek صناديق حاسوب عالية الجودة، وحلول تبريد، ووحدات تزويد طاقة، وملحقات. تصفح موقعنا الإلكتروني للاطلاع على أفضل المنتجات والملحقات.

أيس جيك | اشترِ حافظات وملحقات كمبيوتر عالية الجودة

Acegeek offers high-quality computer cases, cooling solutions, power supplies, and peripherals. Explore our website for top-notch products & accessories.

المدونة

التصفح الحالي：Radiator Fans vs Case Fans