Reviews                                                         

How to Build a High-Airflow PC Without Overspending

I have seen builders spend $180 on a liquid cooler, $70 on glowing fans, another $30 on cable extensions, and still run hotter than a boring mesh-front case with three sensible 120mm PWM fans, because the expensive build was starving the GPU while the cheap build fed it clean intake air. Why pay twice?

That is the uncomfortable truth behind PC airflow: heat does not care about your RGB theme. It does not care about tempered glass. It does not care that a product page says “gaming.” Heat follows pressure, restriction, distance, dust, fan curves, and watts.

Modern hardware makes this worse. NVIDIA lists the RTX 4090 Founders Edition at 450W total graphics power, 304mm long, 137mm wide, 61mm thick, with an 850W minimum system power recommendation and a 36mm cable-clearance note around the power connector on its 

. That is not a little card asking politely for air. That is a space heater with DisplayPort.

So the question is not “How many fans can I install?” The question is uglier: 

where does the GPU get fresh air, where does hot air leave, and how much money are you wasting before answering that?

The best PC airflow upgrade is usually not a premium cooler. It is the case.

A good airflow case has a low-restriction front or side intake, enough room around the GPU, sensible exhaust paths, removable dust filters, and cable space that does not turn the back panel into a steel wrestling match. A bad case has a sealed front panel, tiny side slits, glass everywhere, and a marketing department calling it “optimized.”

I would start by comparing real chassis layouts inside Acegeek’s 

 before touching the fan budget. The reason is simple: if the case blocks intake, every fan you add becomes a louder apology.

A mesh front PC case is not automatically perfect, but it gives you margin. Margin matters.

When intake is restricted, the front fans spin harder, noise rises, dust packs faster into narrow vents, and the GPU starts recycling warmer internal air. In a budget airflow PC build, I would rather buy a modest mesh-front ATX or M-ATX case with three decent fans than buy a luxury glass case and then try to rescue it with six screaming fans.

Hard truth: a “silent” case with a closed front panel often becomes louder than a mesh case, because the fans need higher RPM to pull the same air through smaller openings.

Here is my blunt spending order for a high airflow PC build:

Upgrade DecisionWhat It Really FixesWorth Paying ForUsually OversoldMy Budget OpinionMesh-front or open-intake caseReduces intake restrictionYes, especially for gaming GPUsDecorative glass-heavy frontsSpend here before fans2 front intake + 1 rear exhaustCreates a clean basic airflow pathYesFilling every mount immediatelyBest starting layout140mm fans where supportedMore airflow at lower RPMOftenTiny RGB-only 120mm packsWorth it if case supports them4-pin PWM fansBetter fan curve controlYesExpensive controller ecosystemsBuy practical PWM first360mm AIOCPU heat removalSometimesAs a fix for bad case airflowNot the first fixVertical GPU mountAppearance and clearance changesRarely for airflow“Premium” showcase buildsAvoid unless testedDust filtersCleaner long-term coolingYesUltra-dense filters never cleanedGood only if maintained

If you are choosing fans, do not just buy the prettiest pack. Check whether they are 3-pin DC or 4-pin PWM. Acegeek’s 

 is useful here because fan control is not cosmetic; it decides whether the system can ramp smoothly under load instead of bouncing between too hot and too loud.

But do not get hypnotized by CFM either. CFM ratings are usually measured in ideal conditions, not behind a dust filter, not against a front panel, and not inside a case with a 3-slot GPU dumping heat into the center chamber. Static pressure matters on restrictive intakes and radiators. Noise-normalized performance matters more than a heroic number printed on a box.

Build a PC Fan Configuration That Does Not Fight Itself

A sane PC fan configuration is boring. That is why it works.

For most budget airflow PC builds, I like this starting point:

Optional top exhaust only if temperatures prove it helps.

When builders immediately fill every top mount, they sometimes steal fresh air before it reaches the CPU tower cooler or create a short path where intake air enters and exits without washing over the GPU. More fans can mean worse routing. I have tested this enough times to stop trusting symmetry.

Positive Pressure Is Not Magic, But It Helps

Slight positive pressure means you have more filtered intake than exhaust, so air tends to leave through gaps instead of sucking dust through every crack. For a mesh front PC case, that usually means more intake fan capacity than exhaust fan capacity.

Do not overdo it. Heavy positive pressure can trap heat if exhaust is weak. Heavy negative pressure can pull dust through unfiltered gaps. The target is not ideology. The target is lower GPU hotspot, lower CPU package temperature, stable fan RPM, and less dust after three months.

Run a repeatable load for 15 minutes. Use the same room temperature. Log CPU package temperature, GPU temperature, GPU hotspot, fan RPM, and noise if you can.

If removing the front panel drops GPU temperature by 7°C, you do not have a “fan problem.” You have an intake restriction problem. If removing the side panel barely changes anything, your case airflow may already be fine, and the bottleneck may be the GPU cooler or fan curve.

The Data Center Trick That PC Builders Should Steal

Professional cooling teams do not worship fan count. They watch intake temperature.

The U.S. Department of Energy’s data-center design guidance cites ASHRAE’s recommended air-cooling range of 18°C to 27°C for Class A1–A4 environments, and the same document separates recommended conditions from merely allowable ones. That distinction matters for PCs too: “not crashing” is not the same as “running efficiently and quietly.” 

Lawrence Berkeley National Laboratory also emphasizes that cooling performance should be judged at the equipment intake, not just by the return air or room temperature. In plain PC-builder language: stop staring only at case fan count and start asking what air temperature your GPU and CPU cooler are actually receiving.

That is why I dislike blind “add more exhaust” advice. If your GPU is drinking hot air from a glass-choked lower chamber, a top exhaust fan may make the case look more complete while doing very little for the part that matters.

Want the industry-scale warning sign? Reuters reported in December 2024 that U.S. data-center power demand could reach 6.7% to 12% of total U.S. electricity consumption by 2028, with GPU-heavy AI servers and cooling demand driving much of the increase. Different scale, same physics: watts become heat, and heat has to go somewhere.

First, someone buys a flashy case with poor intake. Then they buy extra fans. Then they buy an AIO. Then they buy better thermal paste. Then they blame the CPU. Meanwhile, the GPU is still starved, the radiator is dumping heat into the case, and the fan curve sounds like a small drone.

Intel’s processor temperature guidance says Tjunction max is the temperature where the processor begins using internal thermal controls to reduce power and limit temperature, and Intel notes that this limit commonly sits around 100°C to 110°C depending on the product. Translation: thermal protection is not a performance plan.

A 240mm or 360mm AIO can be excellent. I am not anti-liquid cooling.

But I am anti-panic-buying. If your case cannot feed cool air to a tower cooler, it may also struggle with radiator placement, tube routing, RAM clearance, motherboard heatsinks, and top-panel exhaust balance. Before buying a large radiator, check Acegeek’s 

My rule: fix case airflow first, then decide whether the CPU cooler is still the limit.

Cheap ARGB fan packs can be fine for a budget airflow PC build, but only if they still move air well, connect cleanly, and allow usable control. A fan that looks good at 1500 RPM but sounds awful at 1500 RPM will eventually be capped at 700 RPM, where it may not do the job.

Small cases are not bad. Lazy small cases are bad.

High-TDP hardware in compact spaces needs cleaner routing, better cable control, and fewer assumptions. Acegeek’s article on 

 makes the point directly: the GPU needs first access to cool intake air, and cables or filters can turn the only intake lane into a heat penalty.

If you are building M-ATX or ITX, your fan layout matters more, not less.

Here is the setup I would build before spending premium money:

Choose a mesh-front or open-intake case with room for your GPU, front fans, rear exhaust, and cable management. For ATX builds, I want enough GPU clearance for the card plus cable bend space. For modern high-end GPUs, that extra 36mm around power cables is not a suggestion I would ignore.

Start with two front intake fans and one rear exhaust fan. If the case supports 140mm fans at the front, I usually prefer them for lower noise at similar airflow. If not, three competent 120mm PWM fans are enough for many mid-range builds.

Use a decent tower cooler for mid-range CPUs. Use a 240mm or 360mm AIO only when CPU wattage, case layout, and radiator clearance justify it. Do not use liquid cooling as a bandage for bad intake.

Keep the GPU’s intake zone open. Avoid placing thick cable bundles, decorative panels, vertical mounts, or support brackets where the GPU fans need air. If you need a support bracket, check fitment carefully; Acegeek’s 

 is relevant because a badly placed bracket can solve sag while blocking airflow.

Cable management is not just aesthetic. A big cable knot in front of intake fans creates turbulence and obstruction. Route front-panel cables flat. Use Velcro. Do not choke the lower front intake because you wanted the back panel to close five minutes faster.

Clean filters every 1–3 months if you have pets, carpet, or a dusty room. Every 3–6 months is fine in cleaner spaces. A clogged mesh filter is just a wall wearing a costume.

The U.S. Department of Energy notes that PCs produce heat and that ENERGY STAR-labeled computers use 30% to 65% less energy than non-labeled computers depending on usage. That is a useful reminder for builders: less wasted power usually means less heat to remove.

A Practical Build Checklist Before You Buy Anything

QuestionWhy It MattersPass ConditionDoes the case have a real intake path?Restriction raises fan RPM and heatMesh, vents, or side intake with usable areaDoes the GPU fit with cable clearance?Bent power cables and blocked side panels create riskGPU length + power connector space confirmedCan the front intake feed the GPU directly?GPU is often the largest heat sourceNo major cable wall or bracket obstructionAre fans PWM or controllable DC?Fan curves decide noise and response4-pin PWM preferred for performance buildsIs top exhaust helping or stealing intake?More fans can short-circuit airflowTested with temperatures, not assumedCan filters be removed easily?Maintenance keeps airflow stableTool-less or quick-access filter cleaningIs radiator clearance real?RAM, tubes, EPS cables, and heatsinks collideMeasured, not guessed

Do this and you will avoid the classic overspend: buying a premium cooler to compensate for a bad case, then buying more fans to compensate for the premium cooler, then accepting a louder PC because the budget is already gone.

A high-airflow PC is a computer build designed to feed cool air directly to heat-producing parts, mainly the GPU, CPU cooler, motherboard VRM, and SSDs, while exhausting hot air without forcing fans to fight blocked panels, tangled cables, or overloaded dust filters. In practice, that means a low-restriction case, sensible fan placement, clean cable routing, and temperature testing under real workloads.

How many fans do I need for good PC airflow?

Most gaming PCs need three well-placed fans for good airflow: two filtered intake fans at the front or side and one rear exhaust fan, with extra top exhaust added only when testing shows lower CPU or GPU temperatures without raising noise. More fans can help, but only when they support the air path instead of disrupting it.

Is a mesh front PC case better than a glass front case?

A mesh front PC case is usually better for airflow because it gives intake fans a lower-resistance path to pull cool room air toward the GPU and CPU cooler, while many glass-front cases depend on narrow side vents that raise restriction and fan noise. Glass can still work, but it needs smarter side intake or bottom intake design.

Should I buy an AIO cooler for a budget airflow PC build?

An AIO cooler is worth buying for a budget airflow PC only when the CPU heat load, radiator clearance, fan placement, and case exhaust path justify the extra cost over a good air cooler. For many mid-range builds, improving case intake and using a competent tower cooler gives better value than jumping straight to liquid cooling.

How do I improve PC airflow without spending money?

You can improve PC airflow without spending money by cleaning dust filters, removing intake obstructions, rerouting cables, testing fan direction, adjusting fan curves, and checking whether top exhaust fans are helping or stealing fresh air before it reaches hot components. The cheapest airflow upgrade is often measurement, because it stops you from buying the wrong fix.

Final Thoughts: Build Cooler Before You Buy Louder

Do not start with a shopping cart. Start with the heat path.

Map your intake, GPU clearance, CPU cooler route, exhaust path, dust filters, and cable bundles. Then test one change at a time with real temperatures. After that, buy only what the data says you need: maybe a better mesh-front case, maybe two PWM fans, maybe a cleaner radiator layout, maybe nothing.

Your next step is simple: open your current case, take one photo of the front intake path and one photo of the GPU area, then compare the build against this checklist before spending another dollar on cooling.

How to Build a High-Airflow PC Without Overspending

The Cooling Lie Nobody Wants to Admit

Airflow is leverage.

I have seen builders spend $180 on a liquid cooler, $70 on glowing fans, another $30 on cable extensions, and still run hotter than a boring mesh-front case with three sensible 120mm PWM fans, because the expensive build was starving the GPU while the cheap build fed it clean intake air. Why pay twice?

That is the uncomfortable truth behind PC airflow: heat does not care about your RGB theme. It does not care about tempered glass. It does not care that a product page says “gaming.” Heat follows pressure, restriction, distance, dust, fan curves, and watts.

Modern hardware makes this worse. NVIDIA lists the RTX 4090 Founders Edition at 450W total graphics power, 304mm long, 137mm wide, 61mm thick, with an 850W minimum system power recommendation and a 36mm cable-clearance note around the power connector on its RTX 4090 specification page. That is not a little card asking politely for air. That is a space heater with DisplayPort.

So the question is not “How many fans can I install?” The question is uglier: where does the GPU get fresh air, where does hot air leave, and how much money are you wasting before answering that?

Start With the Case, Not the Cooler

The best PC airflow upgrade is usually not a premium cooler. It is the case.

A good airflow case has a low-restriction front or side intake, enough room around the GPU, sensible exhaust paths, removable dust filters, and cable space that does not turn the back panel into a steel wrestling match. A bad case has a sealed front panel, tiny side slits, glass everywhere, and a marketing department calling it “optimized.”

I would start by comparing real chassis layouts inside Acegeek’s PC case lineup, then reading the brand’s own PC case selection guide before touching the fan budget. The reason is simple: if the case blocks intake, every fan you add becomes a louder apology.

The Mesh Front PC Case Rule

A mesh front PC case is not automatically perfect, but it gives you margin. Margin matters.

When intake is restricted, the front fans spin harder, noise rises, dust packs faster into narrow vents, and the GPU starts recycling warmer internal air. In a budget airflow PC build, I would rather buy a modest mesh-front ATX or M-ATX case with three decent fans than buy a luxury glass case and then try to rescue it with six screaming fans.

Hard truth: a “silent” case with a closed front panel often becomes louder than a mesh case, because the fans need higher RPM to pull the same air through smaller openings.

Spend Where Air Actually Moves

Here is my blunt spending order for a high airflow PC build:

Upgrade DecisionWhat It Really FixesWorth Paying ForUsually OversoldMy Budget OpinionMesh-front or open-intake caseReduces intake restrictionYes, especially for gaming GPUsDecorative glass-heavy frontsSpend here before fans2 front intake + 1 rear exhaustCreates a clean basic airflow pathYesFilling every mount immediatelyBest starting layout140mm fans where supportedMore airflow at lower RPMOftenTiny RGB-only 120mm packsWorth it if case supports them4-pin PWM fansBetter fan curve controlYesExpensive controller ecosystemsBuy practical PWM first360mm AIOCPU heat removalSometimesAs a fix for bad case airflowNot the first fixVertical GPU mountAppearance and clearance changesRarely for airflow“Premium” showcase buildsAvoid unless testedDust filtersCleaner long-term coolingYesUltra-dense filters never cleanedGood only if maintained

If you are choosing fans, do not just buy the prettiest pack. Check whether they are 3-pin DC or 4-pin PWM. Acegeek’s 3-pin vs 4-pin PC fan guide is useful here because fan control is not cosmetic; it decides whether the system can ramp smoothly under load instead of bouncing between too hot and too loud.

But do not get hypnotized by CFM either. CFM ratings are usually measured in ideal conditions, not behind a dust filter, not against a front panel, and not inside a case with a 3-slot GPU dumping heat into the center chamber. Static pressure matters on restrictive intakes and radiators. Noise-normalized performance matters more than a heroic number printed on a box.

Build a PC Fan Configuration That Does Not Fight Itself

A sane PC fan configuration is boring. That is why it works.

For most budget airflow PC builds, I like this starting point:

Two front or side intake fans.
One rear exhaust fan.
Optional top exhaust only if temperatures prove it helps.

That is it.

When builders immediately fill every top mount, they sometimes steal fresh air before it reaches the CPU tower cooler or create a short path where intake air enters and exits without washing over the GPU. More fans can mean worse routing. I have tested this enough times to stop trusting symmetry.

Positive Pressure Is Not Magic, But It Helps

Slight positive pressure means you have more filtered intake than exhaust, so air tends to leave through gaps instead of sucking dust through every crack. For a mesh front PC case, that usually means more intake fan capacity than exhaust fan capacity.

Do not overdo it. Heavy positive pressure can trap heat if exhaust is weak. Heavy negative pressure can pull dust through unfiltered gaps. The target is not ideology. The target is lower GPU hotspot, lower CPU package temperature, stable fan RPM, and less dust after three months.

The Cheap Test That Beats Guessing

Run a repeatable load for 15 minutes. Use the same room temperature. Log CPU package temperature, GPU temperature, GPU hotspot, fan RPM, and noise if you can.

Then test one change at a time:





Front panel on vs. off



Dust filter clean vs. dusty



Top fans on vs. off



Side panel on vs. off



GPU support bracket installed vs. removed if it blocks bottom intake



Front intake fans at 900 RPM vs. 1200 RPM

If removing the front panel drops GPU temperature by 7°C, you do not have a “fan problem.” You have an intake restriction problem. If removing the side panel barely changes anything, your case airflow may already be fine, and the bottleneck may be the GPU cooler or fan curve.



The Data Center Trick That PC Builders Should Steal

Professional cooling teams do not worship fan count. They watch intake temperature.

The U.S. Department of Energy’s data-center design guidance cites ASHRAE’s recommended air-cooling range of 18°C to 27°C for Class A1–A4 environments, and the same document separates recommended conditions from merely allowable ones. That distinction matters for PCs too: “not crashing” is not the same as “running efficiently and quietly.” 

Lawrence Berkeley National Laboratory also emphasizes that cooling performance should be judged at the equipment intake, not just by the return air or room temperature. In plain PC-builder language: stop staring only at case fan count and start asking what air temperature your GPU and CPU cooler are actually receiving.

That is why I dislike blind “add more exhaust” advice. If your GPU is drinking hot air from a glass-choked lower chamber, a top exhaust fan may make the case look more complete while doing very little for the part that matters.

Want the industry-scale warning sign? Reuters reported in December 2024 that U.S. data-center power demand could reach 6.7% to 12% of total U.S. electricity consumption by 2028, with GPU-heavy AI servers and cooling demand driving much of the increase. Different scale, same physics: watts become heat, and heat has to go somewhere.

Where Overspending Usually Happens

The overspending pattern is predictable.

First, someone buys a flashy case with poor intake. Then they buy extra fans. Then they buy an AIO. Then they buy better thermal paste. Then they blame the CPU. Meanwhile, the GPU is still starved, the radiator is dumping heat into the case, and the fan curve sounds like a small drone.

Intel’s processor temperature guidance says Tjunction max is the temperature where the processor begins using internal thermal controls to reduce power and limit temperature, and Intel notes that this limit commonly sits around 100°C to 110°C depending on the product. Translation: thermal protection is not a performance plan.

A 240mm or 360mm AIO can be excellent. I am not anti-liquid cooling.

But I am anti-panic-buying. If your case cannot feed cool air to a tower cooler, it may also struggle with radiator placement, tube routing, RAM clearance, motherboard heatsinks, and top-panel exhaust balance. Before buying a large radiator, check Acegeek’s top-radiator clearance guide and compare it with the CPU cooler category.

My rule: fix case airflow first, then decide whether the CPU cooler is still the limit.

The RGB Fan Pack Trap

Cheap ARGB fan packs can be fine for a budget airflow PC build, but only if they still move air well, connect cleanly, and allow usable control. A fan that looks good at 1500 RPM but sounds awful at 1500 RPM will eventually be capped at 700 RPM, where it may not do the job.

Buy airflow first. Buy lighting second.

The Small Case Trap

Small cases are not bad. Lazy small cases are bad.

High-TDP hardware in compact spaces needs cleaner routing, better cable control, and fewer assumptions. Acegeek’s article on small cases and high-TDP hardware makes the point directly: the GPU needs first access to cool intake air, and cables or filters can turn the only intake lane into a heat penalty.

If you are building M-ATX or ITX, your fan layout matters more, not less.

My Budget Airflow Blueprint

Here is the setup I would build before spending premium money:

Case

Choose a mesh-front or open-intake case with room for your GPU, front fans, rear exhaust, and cable management. For ATX builds, I want enough GPU clearance for the card plus cable bend space. For modern high-end GPUs, that extra 36mm around power cables is not a suggestion I would ignore.

Fans

Start with two front intake fans and one rear exhaust fan. If the case supports 140mm fans at the front, I usually prefer them for lower noise at similar airflow. If not, three competent 120mm PWM fans are enough for many mid-range builds.

CPU Cooling

Use a decent tower cooler for mid-range CPUs. Use a 240mm or 360mm AIO only when CPU wattage, case layout, and radiator clearance justify it. Do not use liquid cooling as a bandage for bad intake.

GPU Air

Keep the GPU’s intake zone open. Avoid placing thick cable bundles, decorative panels, vertical mounts, or support brackets where the GPU fans need air. If you need a support bracket, check fitment carefully; Acegeek’s GPU sag bracket guide is relevant because a badly placed bracket can solve sag while blocking airflow.

Cable Routing

Cable management is not just aesthetic. A big cable knot in front of intake fans creates turbulence and obstruction. Route front-panel cables flat. Use Velcro. Do not choke the lower front intake because you wanted the back panel to close five minutes faster.

Dust

Clean filters every 1–3 months if you have pets, carpet, or a dusty room. Every 3–6 months is fine in cleaner spaces. A clogged mesh filter is just a wall wearing a costume.

The U.S. Department of Energy notes that PCs produce heat and that ENERGY STAR-labeled computers use 30% to 65% less energy than non-labeled computers depending on usage. That is a useful reminder for builders: less wasted power usually means less heat to remove.

A Practical Build Checklist Before You Buy Anything

Use this before checkout:

QuestionWhy It MattersPass ConditionDoes the case have a real intake path?Restriction raises fan RPM and heatMesh, vents, or side intake with usable areaDoes the GPU fit with cable clearance?Bent power cables and blocked side panels create riskGPU length + power connector space confirmedCan the front intake feed the GPU directly?GPU is often the largest heat sourceNo major cable wall or bracket obstructionAre fans PWM or controllable DC?Fan curves decide noise and response4-pin PWM preferred for performance buildsIs top exhaust helping or stealing intake?More fans can short-circuit airflowTested with temperatures, not assumedCan filters be removed easily?Maintenance keeps airflow stableTool-less or quick-access filter cleaningIs radiator clearance real?RAM, tubes, EPS cables, and heatsinks collideMeasured, not guessed

Do this and you will avoid the classic overspend: buying a premium cooler to compensate for a bad case, then buying more fans to compensate for the premium cooler, then accepting a louder PC because the budget is already gone.

FAQs

What is a high-airflow PC?

A high-airflow PC is a computer build designed to feed cool air directly to heat-producing parts, mainly the GPU, CPU cooler, motherboard VRM, and SSDs, while exhausting hot air without forcing fans to fight blocked panels, tangled cables, or overloaded dust filters. In practice, that means a low-restriction case, sensible fan placement, clean cable routing, and temperature testing under real workloads.

How many fans do I need for good PC airflow?

Most gaming PCs need three well-placed fans for good airflow: two filtered intake fans at the front or side and one rear exhaust fan, with extra top exhaust added only when testing shows lower CPU or GPU temperatures without raising noise. More fans can help, but only when they support the air path instead of disrupting it.

Is a mesh front PC case better than a glass front case?

A mesh front PC case is usually better for airflow because it gives intake fans a lower-resistance path to pull cool room air toward the GPU and CPU cooler, while many glass-front cases depend on narrow side vents that raise restriction and fan noise. Glass can still work, but it needs smarter side intake or bottom intake design.

Should I buy an AIO cooler for a budget airflow PC build?

An AIO cooler is worth buying for a budget airflow PC only when the CPU heat load, radiator clearance, fan placement, and case exhaust path justify the extra cost over a good air cooler. For many mid-range builds, improving case intake and using a competent tower cooler gives better value than jumping straight to liquid cooling.

How do I improve PC airflow without spending money?

You can improve PC airflow without spending money by cleaning dust filters, removing intake obstructions, rerouting cables, testing fan direction, adjusting fan curves, and checking whether top exhaust fans are helping or stealing fresh air before it reaches hot components. The cheapest airflow upgrade is often measurement, because it stops you from buying the wrong fix.

Final Thoughts: Build Cooler Before You Buy Louder

Do not start with a shopping cart. Start with the heat path.

Map your intake, GPU clearance, CPU cooler route, exhaust path, dust filters, and cable bundles. Then test one change at a time with real temperatures. After that, buy only what the data says you need: maybe a better mesh-front case, maybe two PWM fans, maybe a cleaner radiator layout, maybe nothing.

Your next step is simple: open your current case, take one photo of the front intake path and one photo of the GPU area, then compare the build against this checklist before spending another dollar on cooling.

Build a high-airflow PC without wasting money on fake cooling upgrades. Learn how to choose a mesh front PC case, fan layout, cable routing, filters, and cooling priorities that actually reduce heat.

Avis

Montez un PC à ventilation optimale sans gaspiller d'argent dans des améliorations de refroidissement inutiles. Découvrez comment choisir un boîtier PC avec façade en mesh, l'agencement des ventilateurs, le passage des câbles, les filtres et les priorités de refroidissement pour une réduction efficace de la chaleur.

Comment monter un PC à haut flux d'air sans se ruiner

Acegeek propose des boîtiers d'ordinateur, des solutions de refroidissement, des alimentations et des périphériques de haute qualité. Découvrez notre site web pour des produits et accessoires haut de gamme.

ACEGEEK | Achetez des boîtiers et accessoires d'ordinateur de haute qualité

Acegeek offers high-quality computer cases, cooling solutions, power supplies, and peripherals. Explore our website for top-notch products & accessories.

Blog

Navigation actuelle：best PC case for airflow