Reviews                                                         

Static Pressure Curves Explained for PC Cooling Fans

A static pressure curve shows how much pressure a fan can build at each airflow rate while it runs at a fixed speed. Airflow (CFM or m³/h) sits on the horizontal axis, and static pressure (mmH₂O or Pa) sits on the vertical axis. The curve slopes downward: the more resistance a fan pushes against, the less air it moves. The part that matters for a real PC is where that curve meets the resistance of your radiator, heatsink, filter, or front panel. Spec sheets list only the two extreme ends of the curve, and neither end occurs inside a case. This guide explains how to read the whole curve, how system resistance and fan speed shift the result, and how to use that knowledge to choose fans for radiators, filtered intakes, and open exhaust positions.

A static pressure curve, usually called a P-Q curve in fan literature, plots pressure (P) against flow (Q) for one fan at one speed. If you want the basics of how the graph is labeled and why buyers should care, ACEGEEK covers them in its 

. This article goes further into how curves behave once a fan is installed.

 makes the key point plainly: maximum airflow occurs at 0 Pa, maximum static pressure occurs at zero airflow, and an installed fan reaches neither. Its operating condition falls somewhere between the two.

Units cause confusion when you compare datasheets. Many PC fan makers quote static pressure in mmH₂O, while industrial datasheets often use Pa. One mmH₂O equals about 9.81 Pa. Airflow appears as CFM or m³/h, and 1 CFM is about 1.7 m³/h. Convert before you compare, and confirm that both numbers describe the same test.

Why Does the Middle of the Curve Matter More Than the Endpoints?

The middle matters because every real installation lives there. A fan that wins at the free-air endpoint or the shut-off endpoint can lose in the region where your build actually operates.

Noctua's own technical comparison of its NF-A12x25 with the NF-F12 and NF-S12A illustrates this. 

Noctua maps the three fans' P/Q curves onto sample impedance curves

 for a typical PC case, heatsink, and radiator. The pressure-optimized NF-F12 had the highest maximum static pressure and the airflow-optimized NF-S12A had the highest maximum airflow. Noctua's argument is that the fan tuned for the mid-section of the curve gave the better balance at the relevant operating points. This is a manufacturer's analysis of its own products, so treat it as a clear explanation of the method rather than independent proof of any single fan's ranking.

The practical takeaway is a qualification of a common buying habit. A higher maximum static pressure number does not automatically make a better radiator fan. What counts is the airflow the fan holds at the pressure your radiator demands, at a speed and noise level you can live with. Two fans with identical shut-off pressure can cross each other on the curve and rank differently in the middle.

How Does System Impedance Turn a Curve Into Real Airflow?

System impedance, also called airflow resistance, is the pressure your hardware needs to push a given amount of air through it. Sanyo Denki's lesson on airflow resistance explains that 

system impedance is typically modeled as a quadratic curve

. Resistance rises with the square of airflow, and the point where that curve crosses the fan's P-Q curve is the operating point. A flat impedance curve means easy airflow. A steep one means a restrictive path.

Because the relationship is quadratic, a restriction becomes expensive quickly. In the idealized model, doubling the airflow through a fixed obstruction requires about four times the pressure.

Suppose a filter and mesh combination needs 0.4 mmH₂O to pass 30 CFM. Under the quadratic model, pushing 60 CFM through it would need about 1.6 mmH₂O. A fan rated at 60 CFM in free air generates almost no pressure at that flow, so it cannot deliver 60 CFM through this obstruction. The fan settles at a lower flow where its curve meets the impedance curve. These numbers are illustrative, not measurements of a real fan or filter, and real airflow in cases is not perfectly quadratic. The direction of the effect is reliable even when the exact values are not.

Fixing impedance can beat swapping fans. A clogged filter or blocked intake path steepens the system curve, which pulls the operating point toward lower airflow no matter which fan you install.

Speed moves the whole curve. A single P-Q curve describes one rotational speed, and a fan running at other speeds has a family of curves. For a given fan, the idealized fan laws say that airflow scales with speed and static pressure scales with the square of speed. Sanyo Denki's lesson states that 

doubling speed gives roughly twice the airflow and four times the static pressure

, which lets you estimate a new curve from a known one.

Combine that with a quadratic system curve, and installed airflow through a fixed restriction scales roughly in proportion to speed in the ideal case. A 20% increase in RPM tends to yield around 20% more airflow through that restriction, even though the fan's own pressure capability rises by roughly 44%. Real systems deviate from this, and the benefit depends on where the operating point sits. But the logic explains a common buying mistake: chasing a high-RPM fan for a restrictive path. Noise and power draw usually climb faster than airflow, so a fan that reaches your needed airflow at lower RPM usually has the better curve for that job.

Static Pressure Curve vs. Fan Speed Curve

Two different graphs share the word "curve." The static pressure curve describes the fan's aerodynamic behavior at a fixed speed. A fan curve in your BIOS or control software maps a temperature to a speed. They answer different questions. The first tells you what the hardware can do at a given RPM. The second tells the system which RPM to use. If radiator fans ramp erratically, the control source may be the problem rather than the fan design. ACEGEEK's walkthrough on 

using coolant temperature or CPU temperature for fan control

What Do Different Curve Shapes Mean for Buying Decisions?

Curve shape signals what a fan was designed to do. The following comparison uses qualitative tendencies, not measured data, because exact curves vary by model:

These categories overlap. ACEGEEK's comparison of 

 explains where each type tends to belong. For help matching a specific fan to a specific position, see the guide on 

choosing between radiator fans and case airflow fans

Why Do Some Fan Curves Dip or Look Uneven?

Some axial fan curves can show a dip or a bumpy region at high pressure and low flow. This is typically the stall region. Comair Rotron's technical paper on axial fan stall describes an impedance-related mechanism: 

as impedance behind the fan increases, static pressure builds at the fan outlet and the air separates from the blades

. The same paper notes that some stall avoidance may be possible through blade design, but the noise signature can suffer.

For a PC builder, the lesson is practical. Avoid choosing a fan whose operating point lands in or near that region. Very dense radiators, closed-off intakes, and heavily restricted filters can push a fan there. In that zone, expect lower airflow and less predictable behavior, with results that depend heavily on installation details. If a published curve shows a pronounced dip, check where your system curve would cross it.

Stacking fans changes the combined curve, but not as neatly as the theory suggests. Sanyo Denki notes that, in theory, 

two identical fans in series double static pressure and two in parallel double airflow

. It also warns that airflow interference often pulls real performance below the theoretical numbers, particularly when fans sit close together.

This is relevant to push-pull radiator setups (roughly series) and to multi-fan intake panels (roughly parallel). Adding a second fan to a radiator can help, but the gain is usually smaller than the theoretical doubling, and noise rises. Spend effort on the first fan's operating point before adding more.

Compare curves with the same ground rules:

Treat any manufacturer curve as a starting estimate. Fan frame thickness, grille, intake spacing, and case shape all affect real results.

Many consumer fans publish only maximum CFM, maximum mmH₂O, RPM, and noise. In that case, use those four values as a coarse filter, then look for independent testing under restriction. The 

 covers which headline specs are useful and which can mislead, and shows why a restrictive path can sometimes be the real culprit instead of the fan itself.

Be wary of one detail: the ratio of maximum pressure to maximum airflow hints at curve type, but it does not define the curve. Two fans can share the same endpoints and have different mid-sections.

How Should You Use a Static Pressure Curve Before You Buy?

What is a static pressure curve on a PC fan?

It is a graph of the pressure a fan can develop at each airflow rate, measured at a fixed speed. It slopes downward, showing that airflow drops as resistance rises. It is the same thing as a P-Q curve.

Is higher static pressure always better for radiators?

No. Maximum static pressure is measured near zero airflow, which never happens in a case. A radiator fan should hold useful airflow at the pressure the radiator creates, with acceptable noise. Check the middle of the curve.

The operating point is where the fan's P-Q curve crosses the system's impedance curve. It indicates the airflow and pressure the fan will approximately deliver in that specific installation.

Why does my fan deliver less airflow than its CFM rating?

Rated CFM usually describes free-air conditions with no resistance. Filters, radiators, heatsinks, and panels add impedance, moving the operating point to lower airflow and higher pressure than the rated maximum.

How does RPM change the static pressure curve?

In the idealized fan laws, airflow scales with speed and static pressure with its square. Doubling RPM gives roughly twice the airflow and four times the pressure. Real fans deviate, and noise rises rapidly.

In theory, two identical fans in series double pressure, but airflow interference usually keeps real performance below that. Push-pull gains can be real but are usually smaller than theory suggests.

Can I compare fans from different brands using their curves?

Only if units, test method, speed, and control mode match. Otherwise the curves are not directly comparable, so look for independent tests at equal noise.

Static Pressure Curves Explained for PC Cooling Fans

A static pressure curve shows how much pressure a fan can build at each airflow rate while it runs at a fixed speed. Airflow (CFM or m³/h) sits on the horizontal axis, and static pressure (mmH₂O or Pa) sits on the vertical axis. The curve slopes downward: the more resistance a fan pushes against, the less air it moves. The part that matters for a real PC is where that curve meets the resistance of your radiator, heatsink, filter, or front panel. Spec sheets list only the two extreme ends of the curve, and neither end occurs inside a case. This guide explains how to read the whole curve, how system resistance and fan speed shift the result, and how to use that knowledge to choose fans for radiators, filtered intakes, and open exhaust positions.

What Does a Static Pressure Curve Show?

A static pressure curve, usually called a P-Q curve in fan literature, plots pressure (P) against flow (Q) for one fan at one speed. If you want the basics of how the graph is labeled and why buyers should care, ACEGEEK covers them in its fan P-Q curve guide. This article goes further into how curves behave once a fan is installed.

Three features define the graph:





Free-air point (maximum airflow): The curve meets the horizontal axis at 0 Pa. This is the fan moving air with nothing in its way.



Shut-off point (maximum static pressure): The curve meets the vertical axis at zero airflow. This is the fan pushing against a completely blocked outlet.



Everything in between: The curve itself, which describes every realistic working condition.

Sanyo Denki's fan fundamentals lesson makes the key point plainly: maximum airflow occurs at 0 Pa, maximum static pressure occurs at zero airflow, and an installed fan reaches neither. Its operating condition falls somewhere between the two.

Units cause confusion when you compare datasheets. Many PC fan makers quote static pressure in mmH₂O, while industrial datasheets often use Pa. One mmH₂O equals about 9.81 Pa. Airflow appears as CFM or m³/h, and 1 CFM is about 1.7 m³/h. Convert before you compare, and confirm that both numbers describe the same test.

Why Does the Middle of the Curve Matter More Than the Endpoints?

The middle matters because every real installation lives there. A fan that wins at the free-air endpoint or the shut-off endpoint can lose in the region where your build actually operates.

Noctua's own technical comparison of its NF-A12x25 with the NF-F12 and NF-S12A illustrates this. Noctua maps the three fans' P/Q curves onto sample impedance curves for a typical PC case, heatsink, and radiator. The pressure-optimized NF-F12 had the highest maximum static pressure and the airflow-optimized NF-S12A had the highest maximum airflow. Noctua's argument is that the fan tuned for the mid-section of the curve gave the better balance at the relevant operating points. This is a manufacturer's analysis of its own products, so treat it as a clear explanation of the method rather than independent proof of any single fan's ranking.

The practical takeaway is a qualification of a common buying habit. A higher maximum static pressure number does not automatically make a better radiator fan. What counts is the airflow the fan holds at the pressure your radiator demands, at a speed and noise level you can live with. Two fans with identical shut-off pressure can cross each other on the curve and rank differently in the middle.

How Does System Impedance Turn a Curve Into Real Airflow?

System impedance, also called airflow resistance, is the pressure your hardware needs to push a given amount of air through it. Sanyo Denki's lesson on airflow resistance explains that system impedance is typically modeled as a quadratic curve. Resistance rises with the square of airflow, and the point where that curve crosses the fan's P-Q curve is the operating point. A flat impedance curve means easy airflow. A steep one means a restrictive path.

Because the relationship is quadratic, a restriction becomes expensive quickly. In the idealized model, doubling the airflow through a fixed obstruction requires about four times the pressure.

A Hypothetical Illustration

Suppose a filter and mesh combination needs 0.4 mmH₂O to pass 30 CFM. Under the quadratic model, pushing 60 CFM through it would need about 1.6 mmH₂O. A fan rated at 60 CFM in free air generates almost no pressure at that flow, so it cannot deliver 60 CFM through this obstruction. The fan settles at a lower flow where its curve meets the impedance curve. These numbers are illustrative, not measurements of a real fan or filter, and real airflow in cases is not perfectly quadratic. The direction of the effect is reliable even when the exact values are not.

Where Impedance Comes From in a PC





Front panels and filters: Mesh density, vent geometry, and filter media all add resistance. ACEGEEK's article on how front panel design affects PC case cooling looks at how intake openings influence the pressure that intake fans must overcome.



Radiators: Thickness and fin density set resistance. A thick, dense radiator has a steeper impedance curve than a thin, open one.



CPU heatsinks: Fin spacing and stack depth work the same way.



Everything else: Fan grilles, cable bundles, drive cages, and cramped GPU shrouds all add up.

Fixing impedance can beat swapping fans. A clogged filter or blocked intake path steepens the system curve, which pulls the operating point toward lower airflow no matter which fan you install.



How Does Fan Speed Change the Curve?

Speed moves the whole curve. A single P-Q curve describes one rotational speed, and a fan running at other speeds has a family of curves. For a given fan, the idealized fan laws say that airflow scales with speed and static pressure scales with the square of speed. Sanyo Denki's lesson states that doubling speed gives roughly twice the airflow and four times the static pressure, which lets you estimate a new curve from a known one.

Combine that with a quadratic system curve, and installed airflow through a fixed restriction scales roughly in proportion to speed in the ideal case. A 20% increase in RPM tends to yield around 20% more airflow through that restriction, even though the fan's own pressure capability rises by roughly 44%. Real systems deviate from this, and the benefit depends on where the operating point sits. But the logic explains a common buying mistake: chasing a high-RPM fan for a restrictive path. Noise and power draw usually climb faster than airflow, so a fan that reaches your needed airflow at lower RPM usually has the better curve for that job.

Static Pressure Curve vs. Fan Speed Curve

Two different graphs share the word "curve." The static pressure curve describes the fan's aerodynamic behavior at a fixed speed. A fan curve in your BIOS or control software maps a temperature to a speed. They answer different questions. The first tells you what the hardware can do at a given RPM. The second tells the system which RPM to use. If radiator fans ramp erratically, the control source may be the problem rather than the fan design. ACEGEEK's walkthrough on using coolant temperature or CPU temperature for fan control covers that side of the tuning process.

What Do Different Curve Shapes Mean for Buying Decisions?

Curve shape signals what a fan was designed to do. The following comparison uses qualitative tendencies, not measured data, because exact curves vary by model:





Airflow-oriented fans: Typically show the highest free-air flow and perform best where the air path is open, such as rear exhaust, top exhaust, and mesh intakes. Their pressure often falls off quickly as resistance climbs. Risk: they may lose more airflow than expected behind a dense radiator or filter.



Pressure-oriented fans: Typically hold more airflow as resistance rises, which suits radiators, tight heatsink fins, and dust-filtered intakes. Risk: their advantage can shrink in open positions, where noise may matter more than pressure.



Balanced fans: Aim for good performance across the middle of the curve. Risk: they rarely lead in either extreme, so they suit buyers who want one fan type for several positions rather than the best result in one.

These categories overlap. ACEGEEK's comparison of airflow fans vs static pressure fans explains where each type tends to belong. For help matching a specific fan to a specific position, see the guide on choosing between radiator fans and case airflow fans.

Why Do Some Fan Curves Dip or Look Uneven?

Some axial fan curves can show a dip or a bumpy region at high pressure and low flow. This is typically the stall region. Comair Rotron's technical paper on axial fan stall describes an impedance-related mechanism: as impedance behind the fan increases, static pressure builds at the fan outlet and the air separates from the blades. The same paper notes that some stall avoidance may be possible through blade design, but the noise signature can suffer.

For a PC builder, the lesson is practical. Avoid choosing a fan whose operating point lands in or near that region. Very dense radiators, closed-off intakes, and heavily restricted filters can push a fan there. In that zone, expect lower airflow and less predictable behavior, with results that depend heavily on installation details. If a published curve shows a pronounced dip, check where your system curve would cross it.

How Do Multiple Fans Change the Result?

Stacking fans changes the combined curve, but not as neatly as the theory suggests. Sanyo Denki notes that, in theory, two identical fans in series double static pressure and two in parallel double airflow. It also warns that airflow interference often pulls real performance below the theoretical numbers, particularly when fans sit close together.

This is relevant to push-pull radiator setups (roughly series) and to multi-fan intake panels (roughly parallel). Adding a second fan to a radiator can help, but the gain is usually smaller than the theoretical doubling, and noise rises. Spend effort on the first fan's operating point before adding more.

How Can You Compare Two Fans Fairly?

Compare curves with the same ground rules:





Same speed or same noise level. A fan at 1,800 RPM and a fan at 1,200 RPM give you different curves. Use noise-normalized or equal-RPM comparisons when available.



Same units and axes. Check mmH₂O vs Pa and CFM vs m³/h. Watch for charts that mix units.



Same test method. Different test setups can give different numbers for the same fan. Sanyo Denki describes the multi-nozzle double-chamber method for precise measurement. Fan makers who publish the method deserve more trust than those who publish only the figures.



Same operating region. Compare airflow at a pressure that resembles your system, not at the maximum.



Same control mode. A PWM fan's curve at 100% duty differs from its curve at 60%.

Treat any manufacturer curve as a starting estimate. Fan frame thickness, grille, intake spacing, and case shape all affect real results.

What If a Fan Has No Published Curve?

Many consumer fans publish only maximum CFM, maximum mmH₂O, RPM, and noise. In that case, use those four values as a coarse filter, then look for independent testing under restriction. The 120mm PC fan buying guide covers which headline specs are useful and which can mislead, and shows why a restrictive path can sometimes be the real culprit instead of the fan itself.

Be wary of one detail: the ratio of maximum pressure to maximum airflow hints at curve type, but it does not define the curve. Two fans can share the same endpoints and have different mid-sections.

How Should You Use a Static Pressure Curve Before You Buy?





Identify the position. Radiator, heatsink, filtered intake, open exhaust.



Estimate resistance. Thick radiator, dense fins, fine filter, or tight vents mean a steeper system curve.



Find the pressure you need. Look for airflow at moderate pressures, not just the endpoints.



Compare at equal noise. Pick the fan that holds more airflow at the noise level you can accept.



Check compatibility. Confirm thickness, frame size, connectors, and PWM support.



Verify after installation. Compare temperatures and noise before and after the change. Measured results in your own build beat any estimate.

Frequently Asked Questions

What is a static pressure curve on a PC fan?

It is a graph of the pressure a fan can develop at each airflow rate, measured at a fixed speed. It slopes downward, showing that airflow drops as resistance rises. It is the same thing as a P-Q curve.

Is higher static pressure always better for radiators?

No. Maximum static pressure is measured near zero airflow, which never happens in a case. A radiator fan should hold useful airflow at the pressure the radiator creates, with acceptable noise. Check the middle of the curve.

What is the fan operating point?

The operating point is where the fan's P-Q curve crosses the system's impedance curve. It indicates the airflow and pressure the fan will approximately deliver in that specific installation.

Why does my fan deliver less airflow than its CFM rating?

Rated CFM usually describes free-air conditions with no resistance. Filters, radiators, heatsinks, and panels add impedance, moving the operating point to lower airflow and higher pressure than the rated maximum.

How does RPM change the static pressure curve?

In the idealized fan laws, airflow scales with speed and static pressure with its square. Doubling RPM gives roughly twice the airflow and four times the pressure. Real fans deviate, and noise rises rapidly.

Do two fans double static pressure?

In theory, two identical fans in series double pressure, but airflow interference usually keeps real performance below that. Push-pull gains can be real but are usually smaller than theory suggests.

Can I compare fans from different brands using their curves?

Only if units, test method, speed, and control mode match. Otherwise the curves are not directly comparable, so look for independent tests at equal noise.

Learn how to read a PC fan static pressure curve, how system resistance sets airflow, and what to request from suppliers before choosing radiator or case fans.

Avis

Apprenez à lire la courbe de pression statique d'un ventilateur de PC, comment la résistance du système détermine le flux d'air et ce qu'il faut demander aux fournisseurs avant de choisir un radiateur ou des ventilateurs de boîtier.

Explication des courbes de pression statique des ventilateurs de refroidissement pour PC

Acegeek propose des boîtiers d'ordinateur, des solutions de refroidissement, des alimentations et des périphériques de haute qualité. Découvrez notre site web pour des produits et accessoires haut de gamme.

ACEGEEK | Achetez des boîtiers et accessoires d'ordinateur de haute qualité

Acegeek offers high-quality computer cases, cooling solutions, power supplies, and peripherals. Explore our website for top-notch products & accessories.

Blog

Navigation actuelle：system resistance